Search results for: 'TDS Ladle Slick 1'

Apply with a brush uniformly coating any surface where protection is desired. Parts can be coated hot or cold. After the coating is applied the part or surface is exposed to molten alloy which removes the oil base and solidifies the coating. Touchups or small areas can be corrected during normal production. A torch or other heat source can be used if necessary.

The product contains a blend of natural materials and a unique high temperature synthetic polymer that enhances lubrication and release properties for more difficult applications. It can be diluted with water or solvent.

PLUNGER SLICK® 180 is a high viscosity blend of petroleum polymers designed to provide excellent boundary lubricantion for the plunger tip and sleeve.Apply PLUNGER SLICK® 180 to the shot tip before each casting cycle. Each die casting facility is unique. Production processes, die designs, and operation temperatures vary. Each operator should evaluate the amount applied, based on his/her experience.PLUNGER SLICK® 180 is recommended for plunger tips from 2“ – 7“. This product is to be used as is. It is not water soluble.

DIE SLICK® 26 is a highly concentrated petroleum based emulsion. It incorporates specific chemistries that promote wetting and lubricating dynamics within the die casting process. This product is for the die caster who runs the die temperature between 250°F and 450°F and wants minimal buildup on the die.

POLY SLICK™ 61-G is a beaded, dry-form plunger lubricant designed as a high performance substitute to oil-based lubricants. This product is formulated with a unique blend of the highest quality waxes and additives for rapid wetting and excellent boundary lubrication, allowing for increased shot velocities and extended tip and sleeve life. POLY SLICK™ 61-G plunger beads create less carbon build-up than traditional oil-based plunger lubricants, resulting in cleaner die cavities and machines, along with less porosity. POLY SLICK™ 61-G contains graphite for enhanced lubrication and thermal resistance to meet the demands of your process.The amount of POLY SLICK™ 61-G applied is dependent on the size of the plunger tip and the weight of the casting produced. PACKAGING AND STORAGEPOLY SLICK™ products are available in bags, boxes, drums, and pails. All containers are filled to volume by weight.

DIE SLICK® 150 is soluble oil-based die lubricant formulated for zinc die-casting and some aluminum applications. The product contains natural materials that enhance lubrication and release properties. It can be diluted with water or solvent.

DIE SLICK® Anti-Solder 7 is a soft wax compound which removes solder from hot dies and can serve as a start up conditioner for new dies. Solder Removal: Use DIE SLICK® Anti-Solder 7 only with hot dies (> 450oF). Apply a small amount with a bronze brush or a wood spatula to the accumulated solder and the surrounding area. Apply normal spray pattern of die lubricant and conduct your casting cycle. Die Pretreatment: Raise the die temperature to 450oF, brush on a thin coat of DIE SLICK® Anti-Solder 7. Apply coating several times, allowing time for the compound to adhere to the surface of the die.

POLY SLICK 76P was designed as a substitute to oil based lubricants. Product is in beaded dry form. Dispense a modest amount into the shot sleeve. After injection, it melts and expand rapidly inside the shot sleeve. The fine mists created inside the shot sleeve results in an outstanding lubrication film. Unlike most of the oil based lubricant, it does not produce pollution. POLY SLICK 76P reduces porosity in castings and protects the pour area in shot sleeve from erosion, extending the service life of shot sleeve, and reduce adverse effects from scratches; enhances the casting system life. Increases the tool life of plunger tips, generally doubles the tool life when compared to using oil based lubricants. During casting, the plunger lubricants are completely consumed, not leaving any pollutants from oil based lubricants. The surfaces of castings are clean and bright; without oil marks. No grease stains, no smoke nor air pollution during recycle of gating, runners and biscuits. Main

DIE SLICK 77 is a high temperature lubricant developed specifically for use on ejector pins and other moving parts of the die. DIE SLICK 77 will not gum or carbonize at extreme temperatures assuring continuous free movement of sliding parts.

PLUNGER SLICK® 34 is lubricating anti-seize compound for plunger tips and sleeves in casting aluminum, brass or magnesium. It is viscous grease containing micronized graphite. Desirable consistency for manual or automatic application. For manual application apply at full strength (neat) with brush or swab.

WAY SLICK 220 A is a bacteria-reducing machine lubricant which will extend sump life.